Sea-Bird Electronics SBE 38 Manual do Utilizador Página 41
- Página / 124
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Manual revision 006 Section 4: Deploying and Operating SBE 19plus V2 SBE 19plus V2
41
Status Commands (continued)
GetSD Get and display status data, which contains
data that changes while deployed.
List below includes, where applicable,
command used to modify parameter:
• Device type, Serial number
• Date and time [DateTime=] in
ISO8601-2000 extended format
(yyyy – mm-ddThh:mm:ss)
• Logging status (not logging, logging,
waiting to start at . . ., or unknown status)
• Number of recorded events in event
counter [reset with ResetEC]
• Voltages and currents -
- Main battery voltage
- Back-up lithium battery voltage
- Operating current
- Pump current
- External voltage sensor current (channels
0 and 1) – displays only if 1 or more
channels enabled
- External voltage sensor current (channels
2, 3, 4, and 5) – displays only if 1 or more
channels enabled
- RS-232 sensor current – displays only if
channel enabled
• Memory - [reset with InitLogging]
- Number of bytes in memory
- Number of samples in memory
- Number of additional samples that can
be placed in memory
- Length (number of bytes) of each sample
- Number of casts in memory if in
Profiling mode; number of headers in
memory if in Moored mode
Example: Send GetSD to 19plus V2 (user input in bold, command used to modify parameter in parentheses)
getsd
<StatusData DeviceType = 'SBE19plus' SerialNumber = '01906003'>
<DateTime>2011-06-05T10:53:03</DateTime> [DateTime=]
<LoggingState>not logging</LoggingState>
<EventSummary numEvents = '0'/> [can clear with ResetEC]
<Power>
<vMain>10.1</vMain>
<vLith>8.9</vLith>
<iMain>61.9</iMain>
<iPump>20.6</iPump>
<iExt01>67.2</iExt01>
</Power>
<MemorySummary>
<Bytes>150</Bytes> [can clear with InitLogging]
<Samples>10</Samples> [can clear with InitLogging]
<SamplesFree>4386532</SamplesFree> [can clear with InitLogging]
<SampleLength>15</SampleLength>
<Profiles>1</Profiles> [can clear with InitLogging]
</MemorySummary>
</StatusData>
Notes:
• The DS response contains similar
information as the combined
responses from GetSD and GetCD,
but in a different format.
• Sending GetSD causes the pump to
turn on for a moment, so that the
19plus V2 can measure and output
the pump current. Because the
pump is designed to be water
lubricated, you will hear a noise
when the impeller spins in air.
Running the pump dry for such a
short time will not harm the pump.
• In the example below, only voltage
channel 0 is enabled, so external
voltage current iext2345= (for
channels 2, 3, 4, and 5) is not
shown.
• In the example below, no RS-232
sensor is enabled, so RS-232
sensor current iserial= is not shown.
• If the 19plus V2 is set up with a WET
Labs ECO-FL fluorometer with
Bio-Wiper (Biowiper=Y) and if
OutputExecutedTag=Y, the GetSD
response shows: <Executing/>
to allow time for the Bio-Wiper to
close before it measures the
enabled external voltage currents.
- SBE 19plus V2 1
- SEACAT Profiler 1
- Limited Liability Statement 2
- Table of Contents 3
- Section 1: Introduction 5
- Unpacking SBE 19plus V2 6
- System Description 7
- Specifications 11
- Continued from previous page 12
- Sample Timing (Moored Mode) 14
- Batteries 15
- Battery Endurance 15
- External Power 17
- Data Storage 19
- Data I/O 19
- Magnetic Reed Switch 19
- Vertical Mount 20
- Horizontal Mount 23
- Section 3: 24
- See SeatermV2’s Help files 25
- See Seaterm232’s Help files 25
- Profiling Mode 31
- Moored Mode 32
- Pump Operation - General 33
- Pump Operation - Moored Mode 34
- Real-Time Setup 36
- Timeout Description 37
- Command Descriptions 38
- Status Commands (continued) 40
- Profiling Mode (MP) 58
- Moored Mode (MM) 58
- Data Output Formats 66
- Setup for Deployment 78
- Deployment 79
- Acquiring Real-Time Data 82
- Recovery 84
- Uploading Data 85
- The commands and responses 87
- Command/Data Echo Area 87
- Editing Raw Data File 91
- Corrosion Precautions 92
- Plumbing Maintenance 93
- Replacing Alkaline Batteries 94
- CAUTION: 97
- Do not recharge the Ni-Cad 97
- Barbed caps for cleaning 98
- Pressure Sensor Maintenance 99
- Pump Maintenance 99
- 8-inch socket wrench; 100
- Sensor Calibration 101
- Pressure Sensor 102
- Section 6: Troubleshooting 103
- Problem 4: Program Corrupted 104
- Glossary 105
- Sensor Interface 107
- Real-Time Clock 107
- Sensors 107
- Battery Wiring 108
- Appendix II: 109
- DESCRIPTION 110
- WetLabs=x 110
- AF24173 ANTI-FOULANT DEVICE 114
- AF24173 Anti-Foulant Device 115
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais