Sea-Bird Electronics SBE 38 Manual do Utilizador Página 33
- Página / 104
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Section 4: Setting Up MicroTSG SBE 45
25
Autonomous Sampling
The MicroTSG samples data at pre-programmed intervals, defined by
Interval=, and sends the data to the computer. The MicroTSG does not enter
quiescent (sleep) state between samples.
Examples: Autonomous Sampling Mode (user input in bold)
Example 1: J1 jumper in Normal position (pins 2 and 3), AutoRun=Y.
Set up to take a sample every 20 seconds. Send status command to verify setup. Send power-off
command after all parameters are entered. Assuming that power is always applied:
(Click Connect on Toolbar to wake up.)
S>SINGLESAMPLE=N
S>INTERVAL=20
S>AUTORUN=Y
S>DS (to verify setup)
S>QS
When ready to begin sampling:
(Click Capture on Toolbar to capture data to a file – program requests file name for data to be stored.)
(Click Connect on Toolbar to wake up – sampling begins automatically.)
When ready to stop sampling and go to sleep:
(Press Enter key to get S> prompt.)
S>STOP
S>QS
Example 2: J1 jumper in Normal position (pins 2 and 3), AutoRun=N.
Set up to take a sample every 20 seconds. Send status command to verify setup. Send power-off
command after all parameters are entered. Assuming that power is always applied:
(Click Connect on Toolbar to wake up.)
S>SINGLESAMPLE=N
S>INTERVAL=20
S>AUTORUN=N
S>DS (to verify setup)
S>QS
When ready to begin sampling:
(Click Capture on Toolbar to capture data to a file – program requests file name for data to be stored.)
(Click Connect on Toolbar to wake up.)
S>GO
When ready to stop sampling and go to sleep:
(Press Enter key to get S> prompt.)
S>STOP
S>QS
Example 3: J1 jumper in Autopower position (pins 1 and 2).
Set up to take a sample every 20 seconds. Send status command to verify setup. Remove power
after all parameters are entered.
(Apply power to wake up.)
S>SINGLESAMPLE=N
S>INTERVAL=20
S>AUTORUN=Y
S>DS (to verify setup)
(Remove power.)
When ready to begin sampling:
(Click Capture on Toolbar to capture data to a file – program requests file name for data to be stored)
(Apply power to wake up; sampling begins automatically.)
When ready to stop sampling:
(Remove power.)
To change the setup:
(Apply power to wake up; sampling begins automatically. Press Enter key several times to get S> prompt.)
S>STOP
S> (send desired commands)
(Remove power.)
Notes:
• After waking the
MicroTSG, you may
need to press the Enter
key several times and
send Stop to interrupt
sampling, depending on
how the instrument was
set up the last time it
was used.
• If using the MicroTSG
with the Interface Box,
set up the MicroTSG to
operate in autonomous
sampling mode:
¾ J1 jumper in
Autopower position
(pins 1 and 2)
¾ AutoRun=Y
¾ SingleSample=N
30
- SBE 45 MicroTSG 1
- THERMOSALINOGRAPH 1
- TABLE OF CONTENTS 3
- SBE45 MicroTSG 8
- (Thermosalinograph) 8
- Limited Liability Statement 10
- Table of Contents 11
- Table of Contents SBE 45 12
- Section 1: Introduction 13
- Unpacking MicroTSG 14
- System Description 15
- Specifications 17
- Dimensions and Connector 18
- Sample Timing 19
- Power and Cable Length 21
- Section 3: Installing System 23
- MicroTSG data stream 25
- Power-Up Jumper Check 26
- Installing MicroTSG 27
- See SEATERM’s Help files 28
- Status bar 29
- Command/Data Echo Area 29
- Toolbar 29
- Sampling Modes 32
- Autonomous Sampling 33
- Timeout Description 34
- Command Descriptions 35
- Data Output Format 40
- Section 5: Operating System 42
- Processing Data 44
- Corrosion Precautions 45
- Cleaning and Storage 45
- Sensor Calibration 48
- Section 7: Troubleshooting 49
- Glossary 50
- Sensors 51
- Sensor Interface 51
- Appendix II: 52
- AF24173 Anti-Foulant Device 56
- Index SBE 45 61
- Deployment 62
- MicroTSG (Thermosalinograph) 64
- CALIBRATION SHEETS 66
- 24-Aug-11 -0.00 67
- 24-Aug-11 1.0000000 68
- APPLICATION NOTES 69
- General Discussion 70
- Active Use (after each cast) 71
- Cleaning Materials 72
- For 100 cc of solution: 73
- (recommended) 77
- Temperature Sensors 84
- ITS-90 TEMPERATURE SCALE 88
- APPLICATION NOTE NO. 71 90
- Revised March 2008 90
- 92
- DRAWINGS 96
- WARRANTY POLICY 2010 100
- SOFTWARE WARRANTY 102
- PAYMENT/BILLING INFORMATION 104
Manuais e produtos relacionados com Medição, teste e controlo Sea-Bird Electronics SBE 38
(124 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.097 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais